Mobile phone:0086 15837162981

PRODUCT DISPLAY

TCB-200A White Ink of High Weatherability

來源: 發布時間:2019-04-17

This printing ink is two component baking high-performance ink, aiming at meeting the high requirements of the specific touch screen industry for no discoloration during high temperature baking and excellent UV resistance. It has various advantages, such as good adhesion, excellent physical and chemical resistance. Its obvious predominance lies in temperature tolerance and UV resistance. 

Scope of application: Physical tempered glass, chemical reinforced glass. 

Operation process: Add 10 portions of the TCB-200B hardener into 100 portions of this ink and dilute the mixture, then print with 

the 350-420 mesh halftone.

First coating: Baking at 160℃ for 10min;     Second coating: Baking at 160℃ for 10min;     

Third coating: Baking at 160℃ for 10min;

Forth coating: Covered with the gray ink and baking at 180℃ for 20min.

Technical parameters are shown in the following table. (Take the white ink of this series as an example.)


This printing ink is two component baking high-performance ink, aiming at meeting the high requirements of the specific touch screen industry for no discoloration during high temperature baking and excellent UV resistance. It has various advantages, such as good adhesion, excellent physical and chemical resistance. Its obvious predominance lies in temperature tolerance and UV resistance.

Scope of applications: physical tempered glass, chemical reinforced glass.

Operation process: Add 10 portions of the TCB-200B hardener into 100 portions of this ink and dilute the mixture, then print with

the 350~420-mesh halftone.

First coating: baking at 160℃ for 10 min;        

Second coating: baking at 160℃ for 10 min;     

Third coating: baking at 160℃ for 10 min;

Forth coating: covered with the gray ink and baking at 180℃ for 20min.

Technichal parameters are shown in the following table. (Take the white ink of this series as an example.)

Test Items

Test Methods

Test Results

Recoating test

180, 15min; 4 cycles

Cross-cut adhesion test, 100%

Ultraviolet resistance

UV aging test manufacture procedure,

300-hour continuous irradiation

Cross-cut adhesion test, 100%

Fineness

GB/T 1724-79

8μm

Ultrasonic washing

Ordinary detergent, 65, 2hr

Non-foaming;non-wrinkling;non-discoloring;cross-cut adhesion test, 100%

Boiling resistance

Soaking in 100 deionized water for two hours

Non-foaming;non-wrinkling;non-discoloring;cross-cut adhesion test, 100%

High and low temperature humidity and heat cycle

80, 95% RH (8hr); -20(2hr); ten cycles in total

Non-foaming;non-wrinkling;non-discoloring;cross-cut adhesion test, 100%

Salt spray test

Continuous spray: 35, the solution of 5%NaCL distilled water, 120hr

Non-foaming;non-wrinkling;non-discoloring;cross-cut adhesion test, 100%

Hardness

Mitsubishi Pencil at an angle of 45 degrees, 500-gram force, measuring at different locations for 3 times

2H

Adhesion

Cutting 100 grids, 3M gummed paper, continuously pulling off for 5 times

Cross-cut adhesion test, 100%

Surface resistance

Testing surface resistance at 5 locations (80%RH)

1010Ohm

Acid resistance

Soaking in 25 5% H2SO4 solution for two hours

Non-foaming;non-wrinkling;non-discoloring;cross-cut adhesion test, 100%

Alkali resistance

Soaking in 25 5% NaOH solution for two hours

Non-foaming;non-wrinkling;non-discoloring;cross-cut adhesion test, 100%

Ethanol tolerance

Tester loaded with 200 grams; using the winsey, dipped with over 99% alcohol, to rub back and forth for 100 times

Colorfast; not tarnishing

Solvent (Acetone) resistance

Tester loaded with 200 grams; using the winsey, dipped with chemically pure acetone, to rub back and forth for 50 times

Colorfast; not tarnishing

  1. Usage:

1)Before use, add the matched TCB-200B hardener (in the proportion of 10%) and moderate thinner into the ink and then fully  

       stir the mixture before printing. (As to the transparent ink, black ink, colored ink and silver oil of this series, the hardener 

       should be added in the proportion of 15%. )

    2) The recommended baking temperature is 160℃ and the recommended baking time is 10-20 min. On other conditions, please 

      confirm the feasibility in advance in order not to affect the product quality. 

3) During the multilayer overprint, in order to ensure the quality, the first coating solidifies after baking at 160℃ for 10 min; the 

  second coating solidifies after baking at 160℃ for 15min; the last coating, covered with the TCBT-100 series ink (gray), solidifies 

  after baking at 180℃ for 20min.

4) The selection of the thinner types and the thinner dosage depend entirely on the adjustment of printing mesh number, 

  environmental condition and printing effect.

2. Storage condition:

  Before and after using this series of ink, the ink containers should be kept completely sealed in cool and ventilated places to avoid 

  exposure to open fire and high temperature. 

3. Guarantee period:

  The guarantee period is one year since the production date. Beyond the deadline, please reconfirm the usability.

Note 1: All the above tolerance test data, derived from our test results, is for your reference only and not listed as guarantee value.


先锋影音AV不鲁321资源